2 meter spiral chute processing capacity

2 meter spiral chute processing capacity

2 meter spiral chute processing capacity 1. Introduction: The chute sorting belongs to the inclined surface flow sorting process. Mineral mortar is fed to some inclined grooves or slopes, and under the push of water, the mineral particle group is loose and layered. The upper part of the light mineral quickly flows out of the groove, while the lower layer of minerals with a larger proportion stay inside the groove or discharge from the bottom at a low speed. After obtaining the difference, the selected ore and tailings can be obtained. Spiral chutes are machines for mining and beneficiation, making them ideal for sand mining in coastal areas, riverbanks, sandbanks, and river beds. The product has the characteristics of correct structure, simple installation, small land occupation, easy operation, stable beneficiation, clear screening of ore, large production capacity, high efficiency, high beneficiation enrichment ratio, high recycling rate, and reliable operation. It has the advantages of light weight, moisture prevention, rust prevention, corrosion resistance, and strong applicability to fluctuations in feed volume or density, Granularity, and grade. 2、 The working principle is that the spiral mineral separator is freely placed on the cross (or tripod) of the support table. The same mortar is slowly fed onto the spiral groove surface through a feeding chute installed on the rotating groove head for sorting. A valve type equipment is installed at the tail to obtain a slot, allowing the sorted products to be divided into three (or four) categories according to grade along the radial direction. Change the selection width of each device by adjusting the position of the valve block. The product gathering bucket is a concentric circular tube that distinguishes and converges the intercepted multi-directional mineral flow. The transverse surface of the fiberglass chute and the slope change of the curve are very suitable for selecting fine-grained materials. 2m spiral chute processing capacity III. Characteristics. Spiral beneficiation machines have attracted particular attention among multiple gravity beneficiation machines due to their low power consumption, simple structure, small footprint, simple operation, stable beneficiation, clear screening of ore, no moving parts, convenient maintenance and management, and large processing capacity per unit size. The equipment has a wide or flat groove surface, and the area where mineral mortar flows in a laminar flow is quite large, making it more suitable for processing medium to fine (-4MM) particle sized ores. We have made spiral chutes with diameters of 400, 600, 900, and 1200mm domestically, Ф The processing capacity of 1200mm four heads is about 4-6 tons per hour. The processing capacity of the 2-meter spiral chute is . The structure constitutes an automatic coal washing spiral chute. The spiral concentrator consists of six parts: a feeding homogenizer, a feeding trough, a spiral trough, an equipment selection trough, a product gathering hopper, and a trough bracket (including a cross or triangular frame). The spiral groove formed by connecting rotating discs is a key component. The spiral plate is made of fiberglass (fiberglass reinforced coal gangue) and connected together through screws. The sorting surface of the rotating groove has a pre designed durable wear-resistant layer. It has the advantages of lightweight, sturdy, durable, and durable consumer goods that are not easily damaged. A multi tube feeding homogenizer is installed above the rotating groove to sort minerals equally, making it easy to control. The concentrator does not need to be restricted from being placed on the cross (or tripod) of the support table. The evenly distributed slurry passes through the feeding chute installed at the head end of the spiral groove and slowly feeds onto the rotating groove surface for sorting. The tail of the spiral groove is equipped with a valve type new product acquisition groove, which allows the sorting equipment to be divided into three types (or four types) of new products along the radial direction according to grade. To adjust the orientation of the valve block and change the width of each new product, it is necessary to cut it off. The new equipment gathering bucket is a concentric annular tube that differentially collects and leads selected multi-directional mineral flows. The transverse surface of the fiberglass chute and the slope of the curve change greatly to adapt to the selection of fine-grained materials. 5、 Scope of utilization. The spiral concentrator is suitable for separating fine grained iron ore, Ilmenite, Chromite, pyrite, cassiterite, tantalum niobium ore, placer gold ore, coal, monazite ore, Rutile ore, zircon sand, rare earth ore, and other metal and non-metallic mineral materials with sufficient density ratio difference. 2 meter spiral chute processing capacity 2 meter spiral chute processing capacity

2 meter spiral chute processing capacity

2 meter spiral chute processing capacityRelated Information

• 

  Grooved spiral chute

• 

  Fiberglass spiral chute

• 

  Automatic ore discharge centrifugal conc

• 

  Shaftless drum screen