High frequency vibration spiral chute

High frequency vibration spiral chute

High frequency vibration spiral chute 1. Overview. The high-frequency vibration spiral chute sorting belongs to the slope flow sorting step. Mineral mortar is fed to a partially inclined chute or inclined surface. With the assistance of flowing water, the mineral particle group is not tightly fastened and layered. The lighter mineral material on the upper part is quickly discharged out of the groove, while the heavy mineral material on the lower part is stagnant inside the groove or flows out at a low speed from the lower end. After being connected, the selected ore or tailings are obtained. The spiral concentrator is a mechanical device for mining and beneficiation, making it ideal for sand mining in coastal, river, sand beach, and stream beds. The product has the characteristics of appropriate structure, easy installation, small land occupation, easy operation, stable beneficiation, clear mineral separation, high yield, high-efficiency beneficiation, ultra-high enrichment ratio, high recycling rate, and reliable operation. It has the advantages of light weight, moisture prevention, rust prevention, corrosion resistance, and strong applicability to fluctuations in feed volume and density, Granularity, and grade. 2、 Production principles. The uniform mortar of the high-frequency vibration spiral chute is slowly fed onto the rotating groove surface by the feeding groove installed at the beginning of the spiral groove, and selection is carried out. The tail end of the spiral groove is equipped with a valve block type equipment to cut the groove, allowing the sorted products to be divided into three types according to grade along the radial direction. By adjusting the orientation of the valve block to change the selection width of each equipment, the product gathering hopper will merge and export the obtained multi head ore flow differently. The transverse plane and curve slope of the fiberglass spiral chute are different, especially suitable for the selection of small particle materials. High frequency vibration spiral chute III. Features: the spiral chute of high frequency vibration spiral chute has attracted much attention among various gravity separation machines due to its low power consumption, simple structure, small land occupation, simple operation, stable beneficiation, clear mineral separation, no moving parts, convenient Computerized maintenance management system, large output per unit area, etc. The equipment has a wider and flatter groove surface, and the mortar presents a large laminar flow area, making it more suitable for processing medium to fine (-4mm) particle sized ores. Our country has made fiberglass spiral chutes with diameters of 400, 600, 900, and 1200 millimeters, Ф The processing capacity of 1200MM four head is about 4-6 t/h. High frequency vibration spiral chute . High frequency vibration spiral chute 4. Structural composition: The spiral chute is composed of six parts: a feeding homogenizer, a feeding chute, a rotating chute, an equipment selection chute, a product gathering hopper, and a support bracket (including a cross or triangular frame). The spiral groove formed by connecting rotating discs is a key accessory. The spiral plate is made of fiberglass (fiberglass reinforced coal gangue), and a wear-resistant layer is pre made on the sorting surface of the rotating groove through bolts. It also has the advantages of lightweight, sturdy, and long-lasting consumer goods. The spiral groove is equipped with a multi tube feeding homogenizer for ore dressing, which is easy to operate. The mineral sorting device is freely placed on the cross (or tripod) of the support table. The evenly divided mineral mortar is slowly fed onto the spiral groove surface through the feeding groove installed at the beginning of the rotating groove for selection. The bottom of the rotating groove is equipped with a valve block type new product acquisition groove, which allows the sorted new products to be divided into three categories (or four categories) of new equipment along the radial direction according to grade. Change the cutting width of each new product by adjusting the orientation of the valve block. The new product gathering bucket is a concentric circular tube that gathers and exports the selected variable mineral flows. The cross section and slope of the curve of the fiberglass chute are particularly suitable for the selection of fine particle materials. 5、 Scope of application. The fiberglass spiral chute is suitable for processing 0.6-0.03MM and other veins and minerals, but it is unfavorable for sorting when the mud content is high. Nowadays, it is widely used for processing iron ore, tungsten, tin ore sand, niobium tantalum ore, coastal and riverside placer mines, and sand gold mines. High frequency vibration spiral chute High frequency vibration spiral chute

High frequency vibration spiral chute

High frequency vibration spiral chuteRelated Information

• 

  Grooved spiral chute

• 

  Fiberglass spiral chute

• 

  Automatic ore discharge centrifugal conc

• 

  Shaftless drum screen