Tungsten tin spiral chute selection

Tungsten tin spiral chute selection

Selection of tungsten tin spiral chute 1. Explanation: The chute sorting includes a slope flow sorting process. Mineral mortar is fed to some inclined grooves or slopes, and under the push of water, the mineral particle group becomes loose and layered. The upper layer of light mineral quickly flows out of the groove, while the lower layer of heavy mineral material stays in the groove or is discharged from the bottom at low speed. After being collected, the selected ore and tailings are obtained. Spiral chutes are mining and beneficiation machines, especially ideal for sand mining on coasts, rivers, beaches, and streams. The equipment has the characteristics of suitable structure, simple installation, small land occupation, simple operation, stable beneficiation, clear ore separation, large processing volume, high efficiency, high concentration of beneficiation, high recovery rate, and reliable operation. There are also advantages such as small weight, moisture prevention, rust prevention, less corrosion resistance, and strong adaptability to fluctuations in ore feed volume, concentration, particle size, and grade. 2、 Working principle: The fiberglass spiral chute concentrator does not need to be restricted from being placed on the cross (or tripod) of the support table. The same mineral mortar is slowly fed onto the surface of the rotating groove through the feeding chute installed at the head of the spiral groove for sorting. A valve type equipment is installed at the tail to obtain a slot, allowing the selected products to be divided into three categories (or four categories) according to grade along the radial direction. Change the selection width of each device by adjusting the orientation of the valve block. The product gathering bucket is a concentric circular tube that differentially merges and leads out the intercepted multi-directional mineral flow. The transverse plane and slope of the curve of the spiral concentrator are particularly suitable for the separation of fine-grained materials. Tungsten tin separation spiral chute III. The characteristic spiral chute has attracted more attention among various gravity concentration machines due to its low power consumption, simple structure, small land occupation, simple operation, stable beneficiation, clear ore separation, no moving parts, convenient Computerized maintenance management system, large single area processing capacity, etc. The machine has a wide or gentle groove surface, and the area where the mortar flows in laminar flow is large, which is more suitable for processing medium and fine (-4MM) Granularity ores. Spiral concentrators with diameters of 400, 600, 900, and 1200mm have been produced domestically, Ф The production capacity of 1200mm four heads is about 4-6 T/H. The tungsten tin spiral chute is composed of six parts: a feeding homogenizer, a feeding chute, a spiral groove, a product acquisition groove, an equipment gathering hopper, and a groove bracket (including a cross or triangular frame). The rotating groove connected by spiral blades is the main component. The rotating plate is made of fiberglass (fiber reinforced coal gangue) and connected together through screws. The selected surface of the spiral groove has a pre made durable wear-resistant layer. It also has the advantages of lightweight, sturdy, and long-lasting consumables. The rotating groove is equipped with a multi tube feeding homogenizer for ore separation, which is simple and convenient to control. The mineral screening device does not need to be placed on a cross (or tripod) on a support table. The evenly distributed slurry is slowly fed to the rotating groove surface through the feeding groove installed at the end of the spiral groove head, and sorting is carried out. The tail end of the spiral groove is equipped with a valve type new product selection groove, which allows other new products to be divided into three types (or four types) of new equipment along the radial direction according to grade. Change the selection width of each new product by adjusting the orientation of the valve block. The new product gathering bucket is a concentric circular tube that densely exports the intercepted variable mineral flows. The transverse surface of the fiberglass spiral chute has different slopes, which is very suitable for the separation of fine particle materials. 5、 In the application field, the glass fiber reinforced plastic chute is suitable for separating fine iron ore, ferrotitanium ore, chromite ore, pyrite ore, placer tin ore, tantalum niobium ore, placer gold ore, coal mine, monazite ore, Rutile ore, zircon ore and rare earth ore, and has enough density ratio difference to obtain other metals and non gold minerals. Selection of Tungsten Tin Spiral Chute Selection of Tungsten Tin Spiral Chute

Tungsten tin spiral chute selection

Tungsten tin spiral chute selectionRelated Information

• 

  Grooved spiral chute

• 

  Fiberglass spiral chute

• 

  Automatic ore discharge centrifugal conc

• 

  Shaftless drum screen