Where is the spiral chute equipment available

Where is the spiral chute equipment available

Where is the spiral chute equipment? Introduction: The chute sorting belongs to the inclined surface flow sorting process. Mineral mortar is fed to some inclined grooves or slopes, and under the push of water, the mineral particle group is loose and layered. The upper part of the light mineral quickly flows out of the groove, while the lower layer of minerals with a larger proportion stay inside the groove or discharge from the bottom at a low speed. After obtaining the difference, the selected ore and tailings can be obtained. Spiral chutes are machines for mining and beneficiation, making them ideal for sand mining in coastal areas, riverbanks, sandbanks, and river beds. The product has the characteristics of correct structure, simple installation, small land occupation, easy operation, stable beneficiation, clear screening of ore, large production capacity, high efficiency, high beneficiation enrichment ratio, high recycling rate, and reliable operation. It has the advantages of light weight, moisture prevention, rust prevention, corrosion resistance, and strong applicability to fluctuations in feed volume or density, Granularity, and grade. 2、 The mineral mortar with equal working principles is slowly fed onto the surface of the rotating groove by installing the feeding chute at the end of the spiral groove head, and then selected. The tail of the spiral groove is equipped with a valve block type equipment to select the groove, and the sorted products are divided into three types according to grade along the radial direction. By adjusting the position of the valve block to change the cutting width of each equipment, the product gathering hopper allows the obtained multi head ore flow to be collected and exported separately. The cross section and slope of the curve of the fiberglass chute are very suitable for the sorting of fine particle materials. Where are the three advantages and characteristics of the spiral chute equipment? 1. High efficiency, high recovery rate, and accurate ore sorting; 2. No power required; 3. Lightweight, rust resistant, durable, wear resistant, and corrosion-resistant; 4. Low cost, long application life; Strong applicability to fluctuations in ore feed volume, concentration, particle size, and grade; The friction force on the surface of 6 diamond sand makes the beneficiation effect better than other plastic surfaces. The spiral chute equipment is composed of six parts: a feeding homogenizer, a feeding groove, a spiral groove, a product selection groove, an equipment gathering hopper, and a groove bracket (including a cross or triangular frame). The rotating groove connected by spiral plates is a key component. The rotating plate is made of fiberglass (fiberglass reinforced coal gangue) and is bolted together, with a pre made durable and wear-resistant layer on the selected surface of the spiral groove. It has the advantages of lightweight, sturdy, and long-lasting consumables. The head of the rotating groove is equipped with a multi tube ore feeder to evenly separate minerals, making it easy to control. The sorting machine is not limited to stacking on the cross (or tripod) of the support table. Uniform mineral mortar is slowly fed onto the rotating groove surface through the feeding chute at the end of the spiral groove head, and sorting is carried out. The bottom of the spiral groove is installed in a valve block type new product cutting groove, allowing other new equipment to be selected and classified into three types (or four types) of new equipment along the radial direction according to grade. Change the acquisition width of each new product by adjusting the orientation of the valve block. The new product gathering bucket is a concentric circular tube that gathers and leads out the selected multi head ore flow. The lateral plane of the spiral concentrator, with a change in the slope of the curve, is extremely suitable for the separation of fine particle materials. 5、 Scope of application The spiral chute can be used to separate fine grained iron, ferrotitanium, ferrochrome, ferrosulfide, tin ore, tantalum niobium, gold ore, coal, monazite, Rutile, zircon, rare earth and other metals and nonferrous metals with a completely different specific gravity. Where is the spiral chute equipment? @ @ 000 Where is the spiral chute equipment

Where is the spiral chute equipment available

Where is the spiral chute equipment availableRelated Information

• 

  Grooved spiral chute

• 

  Fiberglass spiral chute

• 

  Automatic ore discharge centrifugal conc

• 

  Shaftless drum screen