2 meter spiral chute processing capacity

2 meter spiral chute processing capacity

The processing capacity of the 2-meter spiral chute is as follows: 1. Overview: The chute sorting of minerals belongs to the inclined surface flow sorting step. The slurry is fed to a inclined chute or slope, and under the push of water, the mineral particle group is loose and layered. The upper layer of light minerals is quickly discharged from the groove, while the lower layer of minerals with high specific gravity stays in the groove or flows out at low speed from the bottom. After each is connected, the selected ore or tailings are obtained. Spiral concentrators are equipment for mining and beneficiation, making them ideal for sand mining and beneficiation in coastal, river, sand banks, and creeks. The equipment has a suitable structure, is installed in a simple and simple manner, occupies a small land area, has simple operability, stable beneficiation, clear separation, strong processing capacity, high efficiency beneficiation enrichment ratio, high recovery rate, and reliable operation. There are also advantages such as lightweight, moisture-proof, rust prevention, corrosion resistance, and strong adaptability to fluctuations in feed volume, concentration, particle size, and grade. 2、 The mineral mortar with uniform technical principles is slowly fed onto the surface of the rotating groove through the feeding chute installed at the end of the spiral groove head, and then sorted. The bottom of the spiral groove is equipped with a valve block type product selection groove, which divides the selected equipment into three categories according to grade along the radial direction. By adjusting the orientation of the valve block to change the cutting width of each product, the equipment gathering bucket allows the obtained variable mineral flow to converge and lead out. The change in slope of the curve on the transverse surface of the fiberglass chute is particularly applicable for the sorting of fine-grained materials. The processing capacity of the 2 meter spiral chute is three highlights and this feature is 1. High efficiency, high recovery rate, and correct mineral sorting; 2. Do not use power; 3. Small weight, anti rust, durable and anti wear, durable and anti corrosion; 4. Low cost, long application life; Strong applicability to fluctuations in ore feed volume, concentration, particle size, and grade; The friction force formed by the surface of 6 diamond sand makes the beneficiation effect better than other plastic surfaces. The 2-meter spiral chute has a processing capacity of . The spiral chute is composed of six parts: a feeding homogenizer, a feeding chute, a rotating chute, an equipment selection chute, a product gathering hopper, and a support bracket (including a cross or triangular frame). The spiral groove formed by connecting rotating discs is a key accessory. The spiral plate is made of fiberglass (fiberglass reinforced coal gangue), and a wear-resistant layer is pre made on the sorting surface of the rotating groove through bolts. It also has the advantages of lightweight, sturdy, and long-lasting consumer goods. The spiral groove is equipped with a multi tube feeding homogenizer for ore dressing, which is easy to operate. The mineral sorting device is freely placed on the cross (or tripod) of the support table. The evenly divided mineral mortar is slowly fed onto the spiral groove surface through the feeding groove installed at the beginning of the rotating groove for selection. The bottom of the rotating groove is equipped with a valve block type new product acquisition groove, which allows the sorted new products to be divided into three categories (or four categories) of new equipment along the radial direction according to grade. Change the cutting width of each new product by adjusting the orientation of the valve block. The new product gathering bucket is a concentric circular tube that gathers and exports the selected variable mineral flows. The cross section and slope of the curve of the fiberglass chute are particularly suitable for the selection of fine particle materials. 5、 Applicable field: The fiberglass chute is suitable for processing 0.6-0.03mm and vein ore as well as sand ore, but it is unfavorable for sorting when the mud content is high. Nowadays, it has been widely used in the processing of iron ore, tungsten, tin, tantalum niobium ore, coastal and riverside ore sands, gold mines, and so on. 2 meter spiral chute processing capacity 2 meter spiral chute processing capacity

2 meter spiral chute processing capacity

2 meter spiral chute processing capacityRelated Information

• 

  Grooved spiral chute

• 

  Fiberglass spiral chute

• 

  Automatic ore discharge centrifugal conc

• 

  Shaftless drum screen